|This listing was for a Vorshlag built race car which SOLD IN DECEMBER 2018. This is just here for reference. We built and campaigned in NASA racing over the 2015 and 2016 seasons and is prepped for wheel to wheel racing. With the new set of 200 treadwear tires it is perfect for endurance racing. The LT1 engine was built by HKE Racing with forged rods and pistons, balanced rotating assembly, new valvetrain, and a brand new stock camshaft. Fresh Quarter Master 7.25" triple disc clutch and light flywheel (removed 50 pounds from drivetrain) attached to the ZF S6-40 6-speed transmission. This 1992 model car has been converted to 1995 GM computer and wiring harness MAF sensor for ease of tuning, with an MSD distributor for reliability.
Front brakes are upgraded to 1996 base spec 13" diameter rotors with fresh PBR calipers and Carbotech XP20 pads throughout. Custom Vorshlag built twin Tilton master cylinder brake setup with balance bar replaced problematic OEM master and plastic brake booster. Fenders are flared for 18x12" wheels and 335mm tires at all 4 corners (which we can sell to you). Professionally built roll cage (which can fit tall people) with recent full repaint inside and out. This car is spotless and beautiful. Car is 2950 pounds and includes a ballast rack for adding weight plates quickly. Includes a sticker new set of 275/40/17 Falken RT-615K tires on the 17x9.5" SSR wheels. This Corvette needs nothing - turn the key and go race today!
Asking Price: SOLD Dec 2018
Miles: Less than 100 track miles since full engine rebuild
Title: Clear Texas title (not registered/inspected)
Engine: Fresh forged LT1 engine, 296 whp/363 wtq
Drivetrain: ZF 6-speed manual, Dana 44, Rear Wheel Drive
Colors: Pure White interior, cage and exterior
Mods: W2W Race prepped, 17x9.5" SSR wheels, 3" brake cooling,
Cobra Suzuka GT seat, full roll cage/nets, lightweight flywheel and triple disc clutch.
FAST, fully prepped, and ready to race!
|vorshlag built cage, interior, safety gear and exterior|
|This section details the roll cage, safety gear, seat, and other aspects of the interior of the chassis. We also show many details of the exterior of the Corvette below, showing the car being painted in August 2016. Every picture on this page can be clicked for a higher resolution image.
SAFETY - No expense was spared for safety and this Corvette has one of the nicest roll cages we have ever built. This NASA certified 6-point cage is built to the limit of the class and well within the NASA CCR specs using 1.75" dia x .120" wall seamless 1018 DOM steel tubing. The tubing was carefully fitted and 100% TIG welded to over-sized base plates welded to the frame. The main hoop and upper bars built for a tall driver (6'3") with a fixed seat mounted to a reinforced floor. No passenger seat is installed but it can be added easily (weight box mounted to reinforced OEM seat mounts).
INTERIOR - Factory dash is lightened on driver's side and replaced with a custom formed aluminum panel on passenger side (painted with texture black paint to reduce glare). Brand new Momo steering wheel and Halon style fire extinguisher on quick-release mount. Racequip window net, Scroth center net and Cobra/Scroth 6-point racing harness. 14" parabolic center rearview mirror, factory driver's side mirror, and 4" convex passenger side mirror. Factory gauges work and are easy to read, with water, digital oil temp and other details. Wired for AMB transponder (not included), OBD style port, digital volt meter, water proof cig lighter port and dual USB power ports in center stack. Roll cage painted body color with SFI padding and aluminum panels covering all frame access holes. Interior is spotless and very nice.
PAINT WORK - The factory paint was stripped, fully body-worked and painted in August 2016 by our friends at Heritage Collision in Sherman, Texas. They also sanded, prepped, primed and painted the full interior and roll cage.
After this 2+ month body and paint process, we brought the Corvette back to Vorshlag. There we fabricated dash panels, reinstalled the seat, then installed the roll cage padding. Our crew then built the false floor and rear aluminum panels.
The Artic White (no pigment) base / clear paint looks exceptional in person. We challenge you to find a cleaner, better looking, C4 Corvette race car anywhere, at any price.
|suspension, brakes, wheels and tires|
This section talks about the suspension and brake upgrades that were added to this Corvette. We also show the wheel and tire packages we have used and tested on this car in two different NASA classing configurations. One of the first systems we tackled on this build was the suspension, which we got dialed in fairly quickly and with nothing more than a set of Hoosier R7s and the springs we jumped into NASA TTC class with some effortless wins and big track record drops.
In Spring 2018 we replaced the OEM rear strut rods to VetteBrakes' tubular, adjustable versions with spherical ends. This was done to replace a couple of worn bushings and to allow additional camber adjustment in the rear. At the same time we installed fresh ball joints and wheel bearings on any corner that needed it - everything is now tight. The Corvette then received a race alignemnt in June 2018 on a Hunter laser rack. It is ready to race!
WHEELS AND TIRES - Due to classing restrictions for NASA TTC class we campaigned this car on this lightweight 17x9.5" SSR wheel and a 245/40/17 Hoosier R7 race tire. The car comes with a set of these SSRs and a brand new sticker set of Falken RT-615K 200 treadwear tires in 275/40/17 (you will see pictures of both tire packages in this ad). We also ran this car in TT2 class for a few evens on an 18x12" Forgestar wheel with 335/30/18 Hoosier A6 race tire up front and a wider 345/35/18 rear size.We added the Grand Sport flares to each fender to clear the 18x12" wheel package
BRAKE SYSTEM UPGRADE SETUP - The brakes were tricky - the class "points" limited us to the "base trim level" brakes for a 1992-96 Corvette. This 1992 model came with 12" diameter front and rear discs, but after checking the factory manuals we found that the base 1995 and 1996 model Corvettes used an upgraded Z51/Z07 13" dia x 1.10" thick front rotor. We therefore upgraded to new 13" Centric premium front discs and rebuilt (and wider) PBR calipers for the Z51 package as well as added new 12" rear discs and calipers. We had excellent results with Carbotech XP20 pads and the car has a new set installed now. To keep things cool we fabricated a custom front brake cooling backing plate with 3" oval inlets. These are plumbed from 3" NACA ducts under the front bumper cover and through 3" hoses. We have not seen measured front caliper temps above 370°F in hard, sustained laps.
DUAL MASTER CYLINDERS - Even after the above brake upgrades, one lingering reliability issue with the brakes were short lived "rebuilt" brake master cylinders and brake boosters. After the 4th master failed, we switched to a custom dual Tilton master cylinder setup that we designed, CNC machined and assembled at Vorshlag. This setup bolts in place of the factory brake booster and master assembly, includes a pedal effort multiplier for better brake feel, and a cockpit adjustable Tilton balance bar. The factory ABS system was maintained and the new setup works VERY WELL and is reliable. With the larger discs, brake cooling, Tilton masters, Motul brake fluid, and Carbotech pads this car can brake with or better than the most modern Corvettes and delivers lap after lap of fade-free stopping.
Again, this car was built around a rigid NASA TC/PTC rule set, but could easily be run in HPDE events as-is, or endurance racing on the current 275mm Falkens. We built the body to fit around 335/30/18 Hoosiers at all 4 corners, but a 275mm Hoosier would fit with inches to spare. We won a lot of races and obliterated TTC track records with this suspension setup.
The fully forged race engine is built within the limit of the NASA TT Letter classes, but that doesn't mean we skimped on anything. Forged H-beam Eagle rods and custom spec'd forged Ross pistons are connected to the balanced OEM crank with ARP rod bolts, making the bottom end bullet proof. The factory camshaft was pitted, and no longer made, so the gurus at HKE Racing Engines had the stock cam measured and then custom built a replacement that shares the factory specs in every way. New OEM pushrods, valve springs, and upgraded retainers and keepers were added to the decked and rebuilt factory cylinder heads. This forged, balanced and blue printed engine was not inexpensive but should last for many seasons of racing.
The 1992 model Corvette was the first year of the LT1 engine, and had a unique speed density air metering system and a somewhat crude engine computer. After fighting with problematic computer and old engine harness, we upgraded to a rebuilt 1995 Corvette computer, a new OEM spec engine wiring harness, and MAF unit. The computer and MAF change were class legal but the correct rubber intake hose was no longer available so we used an aftermarket unit and took 1 point for a custom cod air kit. To make that point worthwhile we then modified the factory air box to triple the surface area for incoming air. A new MSD Optispark style distributor fires the Taylor 409 series spark plug wires. A custom aluminum, double thick, radiator was modified to fit the factory radiator ducting and provides cool temps under all conditions. The A/C compressor was replaced with a billet TPIS A/C delete kit, maintaining the factory belt routing.
The Clutch Masters 7.25" diameter triple disc clutch and pressure plate assembly includes a lightweight flywheel which shaved 50 pounds off the factory dual mass flywheel and single disc clutch. This alone makes the engine rev up and down VERY quickly, which makes shifting easier and frees up drivetrain losses. A McLeod hydraulic throw-out bearing was added and setup to actuate the triple disc clutch. The fresh engine and very lightweight clutch setup made 305 whp and 345 wtq, which had to be de-tuned to meet the class limit 286 whp. We added a vented Peterson oil / air separator and catch can plumbed to both valve covers.
There are $10,000 in receipts for the engine, clutch, wiring, computer, ignition system, cooling system, and other drivetrain components, all of which are very fresh. The engine has less than 50 miles on it since it was rebuilt. These power upgrades have been custom dyno tuned by True Street Motorsports, and the engine had to be de-tuned by nearly 20 whp for TTC class limits.
With unrestricted tuning the engine made 305 whp on a chassis dyno - using a factory camshaft, breathing through a stock throttle body, and exhausting through factory manifolds, catalysts, mufflers and piping. This engine could easily produce another 90-100 whp with an exhaust system and camshaft upgrade alone, and reworked cylinder heads could unleash even more. The road to ST4/TT4 would be an easy one.
Again, this car sold in December 2018. We installed a sticker set of 274/40/17 Falken RT-615K street tires, new ball joints, and wheel bearings in February 2018. This ad will stay up with a price listed until the Corvette sells. Feel free to call us (972-422-7170) or email (email@example.com) with any questions about the car. With an appointment you can view the car at the Vorshlag Motorsports facility.
This is one of those rare race cars that is being sold in a meticulously clean state, inside, out and underhood. It looks damn good as it sits, and even more amazing with the 335mm tire / 18x12" wheel combo. Project Dangerzone ran a 1:21 lap at MSR-Cresson on the 1.7 mile CCW course on a 245mm Hoosier R7, carrying ballast, and does this easily and reliably.
The exterior matches the "bare white" images above, with the 5-spoke wheels SSR wheels and a white painted roof panel. All work on the car has been done at Vorshlag by our trained technicians, except for the custom dyno engine tuning and paint work.